weldinguide.com

all about welding





Filler metal, preheat and PWHT selection guide

Filler metal, preheat and PWHT selection guide

Postby mohd » Sat Oct 26, 2013 4:08 pm

Dear all,

Please find attached filler metal, preheat and PWHT selection guide in excel file for ready use.

regards,
mohd.
Attachments
FILLER METAL SELECTION GUIDE Rev[1]. 1.xls
(99.5 KiB) Downloaded 449 times
mohd
 
Posts: 72
Joined: Mon Jul 08, 2013 2:17 pm

Re: Filler metal, preheat and PWHT selection guide

Postby saachinwar » Sun Nov 17, 2013 10:50 am

Dear Mr Mohd,
Please re-post the attached file as the current file is not downloaded in excel format
it shows encrypted letters and symbols
this file could be very useful for my job so if you can mail me to below ID, it would be great help
hoping for your cooperation

saachinwar@yahoo.com

Thanks in advace
saachinwar
 
Posts: 6
Joined: Tue Nov 05, 2013 7:41 am

Re: Filler metal, preheat and PWHT selection guide

Postby gerdmil » Sun Nov 17, 2013 3:49 pm

Dear Saachinwar,
Since I believe that this problem comes from office suite edition, I have downloaded the file and have done four different editions of it (MS Excel 1995, MS Excel 1997/2000/XP, Open Office Calc 4.0.1, PDF) that you can find here attached. I think this tool is more useful in excel or calc file but if you still cannot open them then you can work on pdf file. Please let us know if it works.
I would like also to thank Mohd for this great tool.
regards
gerdmil
Attachments
Filler metal selection guide_MS EXCEL 95.xls
(39 KiB) Downloaded 304 times
Filler metal selection guide_MS EXCEL 97-00-XP.xls
(86 KiB) Downloaded 326 times
Filler metal selection guide_OPEN OFFICE CALC 4.0.1.ods
(18.68 KiB) Downloaded 336 times
Filler metal selection guide.pdf
(113.72 KiB) Downloaded 460 times
gerdmil
 
Posts: 9
Joined: Fri Jul 12, 2013 10:21 am

Re: Filler metal, preheat and PWHT selection guide

Postby saachinwar » Mon Nov 18, 2013 9:37 am

I am extremely thankful to the member for his quick response in posting these files and also once again thanks to Mohd.
Please keep on posting such valuable info in future also.
Thanks a lot again

saachinwar
saachinwar
 
Posts: 6
Joined: Tue Nov 05, 2013 7:41 am

Re: Duplex SS vs Super Duplex SS welding

Postby saachinwar » Tue Apr 01, 2014 7:34 am

Dear Mr Mohammed,

I have been reading your posts since long time and they are very useful. Time ago you shared very useful Excel file for "Filler metal selection" (as I am working as an estimation engineer, it is very useful for estimation of consumables cost) based on P-nos, but apparently this sheet does not cover all material under various P-nos as per section II. E.g. P-no 10H (Duplex / super duplex SS). Could you please update on this or do you have any other data base that covers all material under section II? Could you please share your tools/files (if any) for selection of filler metal or welding rods for various grades. Or can you guide me how to quickly find out filler metal or welding rod for different metals. It would be very helpful as previous. You can also share it on my below e-mail address.

saachinwar@yahoo.com

Thanks a lot,
Saachin
saachinwar
 
Posts: 6
Joined: Tue Nov 05, 2013 7:41 am

Re: Filler metal, preheat and PWHT selection guide

Postby Logosweld » Tue Apr 29, 2014 4:21 pm

the above guide is very useful for the welders as well as the beginners to know there strategies very well before its implementations
Logosweld
 
Posts: 82
Joined: Thu Mar 13, 2014 10:27 am
Location: India

Re: Filler metal, preheat and PWHT selection guide

Postby saachinwar » Wed Apr 30, 2014 5:24 am

Dear Mr.Logosweld,
I have already gone through the above files but all ferrous/nonferrous materials are not covered in this.(E.g. p no 10H etc) I was looking for excel/pdf file or any programme which can give welding consumable selection for all material covered under ASME section-II part A.
Could you please share your guidance or data base for 'how to select welding electrode/filler as per 'p' numbers' for various material combinations.

Thanks in advance.
saachinwar
 
Posts: 6
Joined: Tue Nov 05, 2013 7:41 am

Re: Filler metal, preheat and PWHT selection guide

Postby Logosweld » Wed May 14, 2014 3:37 pm

gerdmil wrote:Dear Saachinwar,
Since I believe that this problem comes from office suite edition, I have downloaded the file and have done four different editions of it (MS Excel 1995, MS Excel 1997/2000/XP, Open Office Calc 4.0.1, PDF) that you can find here attached. I think this tool is more useful in excel or calc file but if you still cannot open them then you can work on pdf file. Please let us know if it works.
I would like also to thank Mohd for this great tool.
regards
gerdmil


nice and informative attachment
Logosweld
 
Posts: 82
Joined: Thu Mar 13, 2014 10:27 am
Location: India

Re: Filler metal, preheat and PWHT selection guide

Postby Logosweld » Tue May 27, 2014 3:25 pm

this will illustrate about the steps to be taken while dealing with filler metal,preheat situations and other guidance
Logosweld
 
Posts: 82
Joined: Thu Mar 13, 2014 10:27 am
Location: India

Re: Filler metal, preheat and PWHT selection guide

Postby Logosweld » Thu May 29, 2014 3:19 pm

all mentioned points are very much important for the beginners as well as for the all respective welders because these all points are very much clear for all to start their metalworking projects or their work
Logosweld
 
Posts: 82
Joined: Thu Mar 13, 2014 10:27 am
Location: India

Re: Filler metal, preheat and PWHT selection guide

Postby Logosweld » Fri Jun 20, 2014 4:15 pm

the whole post mentioned above is very much important because it contains the actual information as well as informative content so i can say that it all sounds good
Logosweld
 
Posts: 82
Joined: Thu Mar 13, 2014 10:27 am
Location: India


Return to Supporting tools

Who is online

Users browsing this forum: No registered users and 1 guest

cron